Vintage-cellars WineKoolR Slimline 800 User Manual

ASSEMBLY & OPERATION MANUALGOLIATH 400 800WineKoolRTM

INSTALL TOPREPEAT STEP ON PAGE 7 FOR TOP46PRESSPRESSNO HINGEOUTSIDEDO NOT INSTALL HINGES YET !NO HINGEB:TOPTOPRIGHTREARCENTERREARCENTERREARTOP

221 1 443I33 I~ 11 ~7INSTALL CENTER POSTS 2,3 and 4 POSTS “1”ALREADY IN PLACENOTE:ARROWS HAVE TO POINTTO “TOP” PANELTOPSLOTSPOST 1POST 1

~ 12 ~8CELLAR BOTTOMINSTALL BRACES 5 AND 6 (7)(HELPER NEEDED TO HOLD CABINET STEADY)"TABSALIGN TO TABS, PUSH DOWN BRACES 5 (× 4)AND 6 ( or 7) (×

~ 13 ~9PLACE COOLING UNIT IN CABINETCIN COOLING UNIT BOX.( 2 ONLY )CLEAR OPENING PUSH THROUGHGET HELPER TO FASTENINGLEVEL TO OPENING UP TIGHT!REAR

10INSTALL SHELVESTAB REFERENCESTART ATBOTTOMPRESS IN SIDESCLICK SHELFOVER TABSLONGER - Full SizeSHORTER - SlimlineFRONTSHELFTABPRESS~ 14 ~HELPER N

~ 15 ~11ON BOTTOMHINGES ONLYHINGE 1HINGE 3HINGE 3WASHERWASHERAPLACE WASHERS ON BOTTOM HINGES INSERT DOORS (one by one) IN BOTTOM HINGES INSTALL TOP HI

~ 16 ~8HINGE 2PLACE W ASHERS FIRSTSEGNIH POT LLATSNITURN BOTH CENTER LEGSTO RAISE LEGS SLIGHT LYTOPON BOTTOMHINGES ONLYHINGE 1TAPGENT LYW ASHERA 1

~ 17 ~14LEVEL CELLARLEVEL DOORS ADJUST OUTER REAR LEGS TO LEVEL DOORSADJUST ALL LEGS TO MAKE CONTACT WITH THE FLOORNOTE: The weight of a loaded Wine

WALLGGHIDRILL USING 1/4” (6 - 6.5 mm) DRILL BIT AND TAP IN ANCHORSPRESS IN FULLY WALL TIES INTO REAR CONNECTOR PLATES AND SCREW IN SCREWSHI BRACE

TIGHTEN LEGSFULLYPRY OFFCONNECTOR PLATEREUSE LEGFOR TOP HINGE~ 19 ~REMOVE COOLING UNIT AND SHELVESLAY CELLAR DOWNFULLY TIGHTEN LEGSPRY OFF ALL CONNECT

~ 2 ~LOCATING YOUR WINE CELLARProvide 2 1/2Never locate your wine cellar outdoors or in an area with extremes of temperature and humidity. These units

~ 20 ~Calibration option of the temperature sensor.Display of actual temperature by request.Digital temperature sensor.Settings are stored in memory f

MAXIMUM CAPACITIES AND LOADING TIPSMaximum capacities and sample loading arrangements for WineKoolR wine cellars are illustrated below. StandardBurgun

~ 22 ~ Coil is locatedat top of middleback panel- Extendable microfiber duster- Vacuum with suitable tip for 2 1/2” clearance IF: CHECK: T

For detailed information consult the Warrantysection of the "USE and CARE" guide!If your WineKoolR™ cooling unit or cabinet fails to perform

ASSEMBLY & OPERATION MANUALGOLIATH 400 800WineKoolRTM

~ 3 ~x 1x 1BLegs x 10AHinge Washer x 3 Left optional Shelvesx 40TOPLEFTREARTOPRIGHTREARx 1x 1x 2x 4SPACERSpacerx 2CONNECTOR PLATESx 2x 2G,H,I - Slimli

~ 4 ~INSERT CORNER (LEFT ONLY) INSERT CORNER (RIGHT ONLY) Note:Disregard Back RIGHT markingStep 1:Step 2:PLACE 2 BACKS (WITHOUT CUT-OUT) AGAINST WALL

~ 5 ~2BACKPLACE AGAINST WALLBACKWALLBACKFLOORWALLBACKPOST 1POST 1BACKBACKPLACE AGAINST WALLBACK BACKINSERT BACKS WITH CORNERS INTO POSTSINSERT POSTS 1

~ 6 ~LEFTLEFTRIGHTLEFTLIFTLIFT3SPACERLEVELSPACERSPACERPlace SPACERS to getready to insert BOTTOM

~ 7 ~4INSTALL BOTTOM2. REST BOTTOM ON SPACERSOKNOSPACERSPACER4. PULL OUT SPACERSBOTTOMBOTTOMOUTSIDEBACKPRESSBOTTOMBOTTOMPRESSSPACERSPACER

~ 8 ~5HAND PRESS IN ALL CONNECTOR PLATES IN BOTTOMTAP IN CONNECTORS TIGHTLY (NO GAP) WITH CLOSED HAND OR RUBBER MALLETINSTALL BOTTOM CONNECTOR PLATESN

TOPINSTALL TOPA: INSERT TOP VENTCHECK TO ENSURE“FRONT” FACES FRONTVENTVENTOUTSIDEFRONTPRESS FORFIRM LOCK(OPPOSITE SIDE)~ 9 ~6